I denna rapport har det utförts två fallstudier från två olika vindkraftsanläggningar och med hjälp av en utarbetad modell har livscykelkostnaderna jämförts för de två fallstudierna.Resultatet visade att livscykelkostnaden per producerad kWh sjunker allteftersom den installerade effekten blir högre.Kostnadsmodellen som utarbetats och tillämpats för resultaten har visat sig ha hög verifierbarhet då resultaten har varit jämförbara med litterära studier..

Life Cycle Cost, often abbreviated as LCC, is a common tool for comparing the total cost of different alternatives, such as heating and cooling methods. Common heating and cooling methods in Sweden are geothermal energy, district heating and district cooling. This report aims to evaluate how different heating and cooling methods differ from each other while being applied on three different types of buildings, using selected LCC-models. Information about the selected LCC-models wasretrieved from each separate model and its website. Reports and agencies were used as sources for information about the heating and cooling methods.

Extended Producer Responsibility (ERP) is a form of product take-back regulation that requires the producers to manage their products at the end of life. By internalising the products? entire life cycle costs into the market price the ultimate objective of such regulations is to reduce the environmental burden from the products. This Master´s thesis seeks to examine if the total life cycle cost of a product actually is borne by the producer, and if not, predict who will then take this cost. This is done by analysing the market for take-back activities in three different categories of products; electrical and electronic equipment, cars and wind power stations.

In recent years, the Swedish railway track system has been neglected in terms of capacity and maintenance. To adapt the existing system to current traffic load there is a great need for extensive improvement and maintenance. Shortcomings are especially occurring on older embankments running over soft subgrades. To select the most suitable method for reinforcement of the embankment, it is important to evaluate different solutions from a life cycle cost perspective. In long-term perspective, it is often shown that a method with low investment cost causes a higher maintenance cost and a shorter technical lifetime.

Abstract Title: Total Cost of Ownership ? Revealing the true cost of owning and operating equipment. Authors: Anna Bladh Anna Ström Tutors: Michaela Boye, Parts and Service, PTD, Alfa Laval Göran Berg, Parts and Service, PTD, Alfa LavalCharlotta Johnsson, Department of Automatic Control, LTH, Lund UniversityBertil I. Nilsson, Department of Industrial Management and Logistics, LTH, Lund UniversityCarl-Henric Nilsson, Department of Business Administration, Lund University Core issue: ?Which costs should be included in a general Total Cost of Ownership model regarding centrifuges, and what input variables are needed in order to calculate those costs in a user-friendly way and with a maintained level of accuracy?? Purpose: The theoretical purpose of the thesis is to identify the cost items that have the greatest impact on a TCO calculation for a centrifuge.

This report is a thesis for collegeengineering program in structuralengineering at Uppsala University andwas commissioned by the Swedishcontractor Svevia. The study aims toprovide an overview of the mostbeneficial bridge material from bothenvironmental and economic point ofview.The life-cycle analysis covers onlycarbon dioxide emissions, since it isthe most spoken of in today?s climateagenda. Furthermore, this study aims tohighlight which parts, of the systemboundary, that contributes to greatercarbon emissions for the wood- and theconcrete bridge.The Life-cycle cost analysis wascalculated with a lifespan of 40 yearsand covers the basic cost of investment,operating and maintenance, anddecommissioning costs.The analyzed constructions in this studyare existing projects that are almostcompleted. Both bridges were designed tohandle loads up to 60 tons.

A growing number of companies realise that to achieve their environmental goals and satisfy stakeholder expectations, they need to look beyond their own facilities and to involve their suppliers in environmental initiatives. A life cycle approach means that the production system should be optimised as whole, across national boarders and individual organisations taking part all the way from extraction to disposal. This study is a Life Cycle Inventory of resources used when producing a piece of cotton garment and the method is based on the standardisation series of ISO 14040-43. The area of study, Tamil Nadu the most southern state of India, accounts for more than 90% of India?s knitwear exports to Western Europe.

Single vehicle accidents are one of the most common types of accidents that occur on the Swedish road network. Depending on the design of the road, the presence of a crash barrier and embankment on the roadside, the outcome of a roadside collision can lead to serious injuries and even deaths.The aim of this project is to investigate the possibility of improving road safety by designing the optimal roadside area based on the results of a life cycle cost analysis (LCC).The questions that have been answered during the duration of this project are:1) Describe the current technical solutions for roadside area design and the various barrier types used in Sweden.2) Complete an existing mathematical model that has been developed by Hawzheen Karim, for calculating Life-cycle costs for various roadside areas.3) Calculate and compare the life cycle costs for the side area with a barrier and without a barrier.By performing an analysis of the documentation on the current guidelines and rules for shaping the roadside, was it possible to describe the current technical solutions for the formation the roadside as well as the current roadside barriers in use today. A mathematical model for calculating the life cycle costs of different barrier types had already been developed by Hawzheen Karim. This model was supplemented so that it could calculate Life-cycle costs of the roadside region with and without a barrier. After the model was completed, an analysis was performed to obtain Life-cycle costs of a roadside with and without a barrier.The result showed that there is a clear relationship between the slope inclination, fill height, and the rate at which the costs rise.

It generally takes 10 to 12 years for a new drug to hit the market. The pharmaceutical industry invests huge sums in these early stages of research and development. In spite of the rapidly rising research and development expenditures fewer and fewer blockbuster drugs are being developed. Longer lead times and aggressive generic post-patent competition have narrowed the timeframe for the pharmaceutical companies to profit on their investments.In the face of these threats the pharmaceutical industry has developed a battery of strategies to prolong market exclusivity and to maximize return on investment. These emerging strategies are commonly known as Life cycle management (LCM), which actually is more of a concept than a method.

This master?s degree project concerns the combination of a multi dwelling passive house with solar energy for the generation of electricity and domestic hot water (DHW). Different alternatives with either solar thermal systems or photovoltaic (PV) systems are compared with two reference alternatives producing DHW from electricity or district heating. The economical comparison uses a life cycle cost (LCC) perspective based on the present value of expenditures for investment, energy and annual operating and maintenance.The energy yields from the solar energy systems were calculated by hand and with simulation software. Calculation and dimensioning of PV systems were carried out with a software called PVSYST.

The aim of my thesis was to do a Life Cycle Assessment (LCA) of an average thread tap that is manufactured by Dormer Tools AB, and to create a practical model that the company can use in order to study other thread taps from an environmental perspective.The method of LCA is used to investigate the environmental effects of a product during its life cycle. This is a gate-to-grave analysis with focus on steel and thread tap manufacturing, coating procedure, use, waste management and transports. Three common coating types were compared separately. Steel manufacturing answers for the highest energy and raw material consumption under the life cycle of the thread tap. Its emissions contribute to global warming, acidification and eutrophication above others.

It is found that the properties of the record years of 1965-1975 is leaking a lot of energy andthese properties are facing a major energy efficiency. From the energy aspect, the facade isafflicted with poor thermal insulation which is a big problem. To address this problem addinginsulation is a good alternative to reduce overall energy consumption of a building. Thewindows on these buildings are also a problem from the energy point of view. Therefore,there are many reasons considered for energy upgrading.

This report analyzes disposable packaging and returnable packaging with the methods life cycle analysis and life cycle costs analysis. These two different packaging are analyzed through the company Clas Ohlson?s packaging-flow. To get a picture of how the flow works, a visit at the company and email contact have been done with Clas Ohlson to get relevant informationToday Clas Ohlson has a big flow of articles to the stores without larger variations in the demand, with the exception of autumn, which is when customers start shopping for Christmas. Clas Ohlson?s articles are placed on a pallet and are wrapped into plastic-film for protection and to make sure that nothing will be stolen.

Digital preservation is a relatively new subject to Swedish archives. Alhough computers have been used for a long time, preservation has been made on paper and stored on shelves. These days a lot of cities in Sweden have investigated how to best secure the digital information for the future through electronic archiving, e-archives. One option is to hand in the information as soon as possible, but to let the producer keep the information ownership yet some time. The idea is to let the producers of the information answer questions and hand out material, since they are more competent on their field.

The purpose of this thesis is to investigate the fatigue life of two components in different hydraulic quick couplings. The crack which initiates the fatigue failure usually occurs in the bottom of one of the threads. Thus, the threads in the coupling are carefully investigated. A few different approaches for determining the fatigue life are studied for each component. CAD (Computer Aided Design) models for both components are created and analyzed with FEM (Finite Element Method).